For sale Dragster Scoop if interested contact me for pictures call or text 902-888-7984

Posted: Thu, 18 Oct. 2018
Expires: Wed, 16 Jan. 2019

For sale is for thunderbird chrome moly full tube chassis drag car. Wheelbase is 110" Front end, doors, rear, etc is all carbon fibre except doors and quarters. Full rolling chassis, includes ignition, mark Williams driveshaft, radiator n fan Fire suppression system Double beadlock 16" wheels Aluminum third member Proven Wally winning car! Goes straight, never wrecked $32,000
Can call or txt 709-683-8688

Posted: Thu, 18 Oct. 2018
Expires: Wed, 16 Jan. 2019

Selling a 383 sbc stroker, dyno at 600 plus. Block is late model 350 010 block, block was just bored, line honed, decked and magna flux at DWA automotive . Engine has eagle rotating assembly internal balanced with steel crank, h-beam rods and set of srp forged piston with 12.5:1 compression with 64cc heads. Has moroso 7qt stroker oil pan with build in tray and Melling m55 oil pump. Top end of the engine has set of AFR 227cc 64cc heads with 2.10 intake and 1.60 stainless valves. All 16 valves were just replaced along with the valve springs which were replaced with a set of Pac springs #1225 with 300lbs of seat pressure good for .800lift. Camshaft is a comp cams solid mechanical roller with 4-7 swap, has .679-.645 lift. Lifters are comp solid roller lifter, rocker arms are Harland sharp 1.6 ratio with .50 intake offset. Cloyes billet timing chain set, aluminum timing cover, ati fluid damper, AFR TITAN intake and holley 850 xp carburetor , MSD billet distributor..Engine went 9.29 in 2400lb car. Asking $8000obo.. Also have ati converter that was just freshed in june that matches the engine for $900.

Posted: Tue, 16 Oct. 2018
Expires: Mon, 14 Jan. 2019

Have a few bolt in seat belt sets that have expired for NHRA. All are latch style. $50.00 each. All are black in color and are in excellent condition.

Posted: Mon, 15 Oct. 2018
Expires: Sun, 13 Jan. 2019

Dart eagle iron heads215 runners,205 valves,72cc, 383 eagle stroker kit for sbc, stud girdle,roller rockers,all new, also victor junior intake $3000 firm. Also chev 350 turbo transmission fresh rebuilt transgo street/strip shift kit ,no converter $600 firm, 8.5/8.6 gm 10 bolt posi trac unit used less 3000 km,aftermarket hardened $300 firm, duel exhaust for 1970-81 Camaro small block,collector pipes to rear end no tailpipes $100 firm, 2 inner front fenders for 1970-77 Camaro from Texas mint $300 firm,4:11 gm 12 bolt ring/pinion less 1200 miles $100 firm, correct cast 4 barrel intake if rebuilding 1970 Camaro/chevelle ,offers ??? Complete tools enough start small business $10,000 firm, long haul trucker only home every second weekend...902 754 4089....bobs1967cansosd@gmail.com.... stellarton n.s

Posted: Fri, 12 Oct. 2018
Expires: Thu, 10 Jan. 2019

Various 351 and other parts as listed.

Ford Motorsport Camshaft, Unused. 302-351W
I bought this for a project that went nowhere. It was never used, just greased up and shelved for a long time.
It is the same camshaft that Ford used in the 1995 351W powered Mustang Cobra R. Part number M-6250-M50. Hydraulic flat tappet cam. 274/290 .453/.453
$85

Rebuilt Ford 400M V8 Connecting Rods
These were purchased for a project and never used. They are rebuilt/reconditioned connecting rods purchased from P.A.W. (Performance Automotive Warehouse) in the USA back when they still sold car parts. $100

Ford 351C/351M/400M 2V Heads
Open chamber 2V heads. Bare. Need to be rebuilt. Some porting was started on them years ago but never completed.
$100

Early 1970's Ford 351W heads. D0OE era.
3 of them. All of them need to be rebuilt. Some port work started on some of them. $200 for all of them.
$100

351C Closed Chamber 4V Heads.
Need to be rebuilt. Port work was started on one.
Note: These heads have been modified to work on a 302 or 351W block. They will still work on a 351C if a couple of plugs are installed in them. $250

351W short block. Needs rebuild.
The block is a 1979 Truck block that was never machined outside of removing the wear ridge in the cylinder and then manually honing them. New cam bearings were also installed. The crankshaft is from the same engine but the rods and pistons are from a different 351W. The pistons are 0.030" over and are junk but the rods are good. Includes assorted new bearings and a couple of rebuild/gasket kits. Engine stand is not included. $250

Box of carburetor parts
Parts from a 2 disassembled holley carburetors from early 80's mustangs. Also has a rebuild kit for a Holley 4160. $20

Posted: Thu, 11 Oct. 2018
Expires: Wed, 9 Jan. 2019

Wanted msd7al3 ignition box and coil part number 8261

Posted: Wed, 10 Oct. 2018
Expires: Tue, 8 Jan. 2019

Looking for a set of 3-55 or preferably 3-73 gears for an 8.8 ford rear end. Chris 902 849 6297

Posted: Sun, 7 Oct. 2018
Expires: Sat, 5 Jan. 2019

Big block Mopar Indy spray bar valve covers ,Indy name on them ,Indy valley pan (one piece). $350 for valve covers and valley pan .

Posted: Mon, 1 Oct. 2018
Expires: Sun, 30 Dec. 2018

I am on the hunt for a pair of SBC aluminum heads around 215-220cc intake runner.

As well, I am interested in any Victor series intakes that might be sitting on a shelf collecting dust. Maybe a tunnel ram?

Let me know what you have and a price.

Rob
rbaxter@hfx.eastlink.ca
902-499-4121 (text only)

Posted: Wed, 26 Sep. 2018
Expires: Tue, 25 Dec. 2018

pair of M/T slicks lots of running in them 15x14x32 will trade for 15x14 x 27 or 28,29 slics or street tires call 1 902 669 2205 also looking for tunnel ram singe 4 or duel 4 AND A COWL HOOD OR SCOOP to fit a 82 to 87 camaro

Posted: Sun, 23 Sep. 2018
Expires: Sat, 22 Dec. 2018

BRAND NEW MSD DYNAFORCE MINI STARTER FOR V8 OLDS,BUICK,PONTIAC. 4:4-1 REDUCTION 3HP MOTOR. GOOD FOR HIGH COMPRESSION ENGINE.
$250.00 NEVER USED,STILL IN BOX
DR.OLDS@NS.SYMPATICO.CA

Posted: Fri, 21 Sep. 2018
Expires: Thu, 20 Dec. 2018